 |
|
|
|
|
|
 |
 |
|
Carter Diamond multiple point
dressing tools contain solid hard diamonds imbedded in
a special matrix which holds the diamonds securely until
used up. |
 |
They will produce sharp, free-
cutting, non-glazed wheels without taper under tough conditions,
even when badly abused. they are supplied in 7/16"
x 1-1/2" long shanks; clusters have 3/4" x 5?8"
long heads. Other size shanks are available at no extra
charge. Order by catalog number or send us your specifications.
|
| Blade
Diamond Tools for Form Dressing |
 |
|
|
 |
Blade tools contain two elongated diamonds uniformly
exposed in a chisel edge pattern. They are intended
primarily for step and radius dressing, but are
sometimes used for straight dressing of large wheels.
These tools were designed for use
on the Cincinnati Centerless grinder and other machines
which locate the diamond tool on a 15" drag
angle to the grinding wheel. In this way the two
diamonds dress in the same path and share the dressing
burden. These tools can be modified for use on machines
having drag angles other than 15".
|
 |
| No.
501 |
Designed
for form and radius dressing on cam operated
machines. |
|
| No.
501L |
Similar
to No. 501 except the blade is slanted to the
left especially for setup dressing. |
|
| Cluster
Diamond Tools for Semi-Finish Dressing |
|
|
|
 |
Cluster tools contain several diamonds set in a
definite pattern in the tool face. They are recommended
for straight face and side dressing of all large
wheels used for rough and semi-finish grinding.
Tool Nos. 521 to 523 are designed for use with no
drag angle and for side dressing where all the diamonds
share the dressing burden at the same time. Tool
Nos. 531 to 533 are designed to be set up at a 15"
drag angle to the wheel and rotated 120 degrees
when worn. In this way three diamonds share the
dressing burden. Used on centerless, cylindrical
and large surface grinders.
|
|
| No.
521 |
Wheels
to 18" O.D. |
|
| No.
522 |
Wheels
to 24" O.D. |
|
| No.
523 |
Wheels
to 36" O.D. |
|
| No.
531 |
Wheels
to 18" O.D. |
|
| No.
532 |
Wheels
to 24" O.D. |
|
| No.
533 |
Wheels
to 36" O.D. |
|
| Impregnated
Diamond Tools for Finish Dressing |
|
|
|
 |
Impregnated tools contains many small, sharp diamonds
of uniform size evenly distributed throughout a
non-glazing metal matrix. These tools are designed
to be used like a large sing;e pointed diamond tool
for straight face or angle dressing on wheels for
finish and semi-finish grinding. Because of the
many sharp points always in contact with the wheel,
this tool, once set up, need not be touched until
completely worn. Specify wheel size when ordering.
Used on centerless, cylindrical, surface, bench
and cutter grinders.
|
|
| No.
544 |
Light
Duty |
|
| No.
545 |
Medium
Duty |
|
| No.
546 |
Heavy
Duty |
|
| Tandem
Diamond Tools for Rough Form Dressing |
|
|
|
 |
Tandem tool contain three slender, elongated diamonds
set one after the other in depth so as each diamond
is worn out, the next diamond automatically comes
into use. The tool remains sharp until completely
used up. Used for form and radius dressing, internal
dressing, and work where other multiple tools cannot
be used.
|
|
| No.
561 |
Wheels
to 6" O.D |
|
| No.
562 |
Wheels
to 12" O.D. |
|
| No.
563 |
Wheels
to 18" O.D. |
|
| No.
564 |
Wheels
to 24" O.D. |
|
| Profile
Diamond Tools for Rough Form Dressing |
|
|
|
 |
Profile tools contain four elongated diamonds, each
set in the corner of a 3/4 inch square disk. Each
diamond can be adjusted to a variety of different
positions depending upon the application. If used
correctly, the diamonds will remain sharp until
completely worn out. Used on centerless, cylindrical,
surface, and other grinders for profile, form and
general dressing in place of single point tools.
|
|
| No.
571 |
Wheels
to 6" O.D |
|
| No.
572 |
Wheels
to 12" O.D. |
|
| No.
573 |
Wheels
to 18" O.D. |
|
| No.
574 |
Wheels
to 24" O.D. |
|
|
|
|
